Snake Tray Hardware, Snake Trays mounting accessories

Cable Organizer Home Home > Cable Raceways Wire Management Systems > Snake Tray Cable Management > Hardware

View Intersections | View Mounting Brackets | View Accessories

This stud type anchor design allows easy through type fastenings and can be set in bottomless holes. The anchor is pre-assembled to ensure an easy and fast installation. Anchor size is the same as drill bit size for an easy installation. Snake Tray has performed comprehensive testing to guarantee high performance in block, masonry and concrete base materials. Our special Bulged middle section with round and diamond shaped opening design prevents the anchors from spinning in the hole.The anchor will not drop out while setting the overhead.

PART #	Description	PRICE
CM-CA-38	Concrete Anchors	$0.99

Concrete Anchors

This stud type anchor design allows easy through type fastenings and can be set in bottomless holes. The anchor is pre assembled to ensure an easy and fast installation. Anchor size is the same as drill bit size for an easy installation. Snake Tray has performed comprehensive testing to guarantee high performance in block, masonry and concrete base materials. Our special design prevents the anchors from spinning in the hole.The anchor will not drop out while setting the overhead.

PART #	Description	PRICE
CM-501-CA	Concrete anchor for 501 only	$0.90

Concrete Anchors for 501 Series Wall Snake

For Overhead Snake Tray installations these pre-cut and pre chased yellow zinc plated threaded rod for overhead tray installations. The rods are all 3/8” 10/24 high strength steel as per ASTM A36 and available in 1’, 2’ ,3’, 4’,6’, and 8’ lengths. The rods are inserted through the patented Snake Eyes™ and secured with two 3/8” hex nuts nuts and one flat washer. NO additional mounting accessories are necessary.

PART #	Size	PRICE
CM-TR-1	3/8" x 12"	$0.95
CM-TR-2	3/8" x 24"	$2.00
CM-TR-3	3/8" x 36"	$3.00
CM-TR-4	3/8" x 48"	$5.21
CM-TR-6	3/8" x 72"	$5.70
CM-TR-8	3/8" x 96"	$7.50

Threaded Rod

Hanger Bracket for powder –actuated fastening. Design allows for easy installation using any 8mm powder actuated fastening system. Available for both steel and concrete. The new versatile hanger that simplifies threaded rod suspension.

PART #	Description	PRICE
CM-TR-HBS	Hanger Bracket for Steel	$1.40
CM-TR-HBC	Hanger Bracket for Concrete	$1.40

Hanger Bracket for Threaded Rod Suspension

Attachment Hardware

PART #	Description	PRICE
CM-FW-38	Zinc Plated 3/8" Washer	$0.10
CM-HN-38	Zinc Plated 3/8" Hex Nut	$0.10
CM-RC-38	Zinc Plated 3/8" Rod Coupling	$0.40

Related Items

	Gator ETS8 Battery Powered Cable Tray Cutters From $1,096.98 Greenlee's Gator ETS8 Cable Tray Cutters will help you save time, money and energy during cable tray installation. The swift retractable blade cuts cable tray wire up to 5/16" in diameter in just 2 seconds.

	Single Snake Tray 201 Series From $51.00 The 201 Snake Tray is available in four sizes .The tray is a single pocket design that can accommodate up to 24 square inches of cable path equal to a 12” generic basket or ladder type tray or 250 cables .25” OD as per NEC Article 318-9(b)

	Double Snake Tray 201 Series From $85.75 The Double Snake 201 Series has a double packet design providing a natural separation for both voice data cables and fiber cables. The double Snake allows for 50 square inches of cable path holding up to 510 cables .25” OD as per NEC Article 318-9(b) both below raised floors or overhead mounted to walls or suspended from a ceiling.

	501 Series Wall Snake Tray From $41.50 The 501 Series Wall Snake Tray is utilized for long linear installations where space is at a premium. Installers know the difficulty of using cable trays in tight spaces but the wall snake tray is the best solution because they are designed to allow the tray to be directly attached to a wall without the use of brackets . The tray uses integrated mounting rings located along the center spine of the tray. With these rings, no additional brackets or mounting hardware is required.

	601 Series Ladder Snake From $92.20 The new 601 Series of cable trays called Ladder Snake™ is especially designed for ladder racks. Ladder Snake ™ instantly bends by hand without any cutting or clipping to ensure a smooth transition from one ladder rack to another. You just snap Ladder Snake ™601 onto a new ladder to instantly gain greater cable capacity. You can also snap Ladder Snake (TN) 601 HP (half the depth of CM-601-12-8) onto an existing ladder rack to bridge over the existing cable plant to create a new second tier cable path.